(Difference between revisions)
| Revision as of 15:15, 18 August 2006 Peter (Talk | contribs) (→'''Chapter 11. Development of ET<sub>0</sub> computation procedure.''') ← Previous diff |
Revision as of 19:30, 19 August 2006 Peter (Talk | contribs) Next diff → |
||
| Line 1: | Line 1: | ||
| <blockquote> | <blockquote> | ||
| - | ='''Chapter 11. Development of ET<sub>0</sub> computation procedure.'''= | + | ==Development of ET<sub>0</sub> computation procedure.== |
| Since 1972 FAO has used the modified Penman method to estimate the evapotranspiration of a reference crop (Frere and Popov, 1986). Recent comparative studies have however shown the best-performing combination equation of the Penman-Monteith approach which has been adopted by FAO in the methodologies for estimating the crop water requirements (Smith, 1991). The reference evapotranspiration ETo is defined as the rate of evapotranspiration from a hypothetical crop of 12 cm height, with canopy resistance of 69 [s m-1] and a canopy reflection coefficient (albedo) of 0,23. | Since 1972 FAO has used the modified Penman method to estimate the evapotranspiration of a reference crop (Frere and Popov, 1986). Recent comparative studies have however shown the best-performing combination equation of the Penman-Monteith approach which has been adopted by FAO in the methodologies for estimating the crop water requirements (Smith, 1991). The reference evapotranspiration ETo is defined as the rate of evapotranspiration from a hypothetical crop of 12 cm height, with canopy resistance of 69 [s m-1] and a canopy reflection coefficient (albedo) of 0,23. | ||
Revision as of 19:30, 19 August 2006
Development of ET0 computation procedure.
Since 1972 FAO has used the modified Penman method to estimate the evapotranspiration of a reference crop (Frere and Popov, 1986). Recent comparative studies have however shown the best-performing combination equation of the Penman-Monteith approach which has been adopted by FAO in the methodologies for estimating the crop water requirements (Smith, 1991). The reference evapotranspiration ETo is defined as the rate of evapotranspiration from a hypothetical crop of 12 cm height, with canopy resistance of 69 [s m-1] and a canopy reflection coefficient (albedo) of 0,23.
Potential evapotranspiration (ET0) is a vital input to Water Balance calculations, which in turn are a vital part in Crop forecasting. The parameters needed to calculate ET0 are listed below. The data should be in daily form.
Parameter group Parameters Remarks Temperature Maximum and minimum temperature Some ET0 calculation methods use average temperature only. AgrometShell needs both minimum and maximum temperatures. Radiation (MJ/m2) Global radiation Global radiation can be calculated from sunshine hours or sunshine fraction accompanied by latitude and day in the year (Julian Date). Wind Speed (m/sec) Wind speed at 2 meters Formulas are available to convert wind speed for other heights (e.g. 10 meters) into a 2 meter value. Optional: relative humidity (%) Maximum and minimum relative humidity during the day. Although this parameter is not essential it improves the ET0 calculations substantially. In AgrometShell relative humidity can be calculated from vapour pressure measurements. The ET calculation routine used in AgrometShell have been developed by Dr. Marcello Donatelli (http://www.sipeaa.it/mdon/). He publishes a number of his agrometorology methods on the web (for on-line ET calculation examples see: http://www.sipeaa.it/wfet/).
Checking data availability using AgrometShellIn order to check whether enough input data are available to calculate ET0 AgrometShell is used. In AgrometShell activate the Tools – Potential ET – Manual function.
The manual ET0 calculation window 
On the left side the input parameters are specified. On the right side, the outcome is generated, once the Calculate>> button is pressed. Clear the parameters on the left side of the screen and fill them with your own data. Try to calculate. If a value is calculated for the ET0, the top right value (Reference ET) is filled. The From… buttons make it possible to calculate the following parameters in an alternative way:
- Day number in the year
- Global radiation
- Vapour pressure
Calculating ET0 using external ASCII files.
The ET0 calculations can be done in AgrometShell using data from the database or data in external ASCII files. In this paragraph the second option will be outlined.
The input file should be in FAO format. You can check this by displaying the file with the View – Data – As columns function 
Display the FAO format file in the Agrometshell Viewer. The headers explain the data prevalent in the columns. 
Now activate the Tools-Potential ET-From file function 
Specify the lay-out of the file to AgrometShell with the following screen 
View the results. Notice the ET0 column (column 6) 
After calculating the ET0 values need to be imported into AgrometShell using the following procedure on ASCII import.
