Chapter19 - CM Box User Guide

Revision as of 14:16, 22 September 2006; view current revision
←Older revision | Newer revision→

6.2. Gathering all into the FAO AgroMetShell (AMS) crop simulation software.

Entering data for a crop water balance calculation

For a water balance calculation the following data are needed:

Weather data

Actual Rainfall for the period of he water balance calculation (up to the current dekad). There are three ways to read these data into AgrometShell.

Using the Database-Weather-Dekad function.
When the data come as ASCII files, using the Database-Import-from ASCII file
When the rainfall comes in the form of images, it can be imported through the Database-Import-from image function.

Normal Rainfall for 36 dekads in the year. These data can be read into AgrometShell in the same way as actual rainfall.

Actual ET₀ data for the season up to the current dekad. The ET₀ data can be calculated from its base data (temperatures, windpeed etc.. ) using the Database-Calculate-Formula function or the Tools-Potential ET-from file function. In case the ET₀ values are already calculated, the can be entered in the three ways mentioned above. Although actual ET₀ data will improve the outcome of the water balance calculation, AgrometShell can use normal values instead.

Normal ET₀ data for the season up to the current dekad. As outlined for actual data, the normal ET₀ data can be either calculated or entered manually. The water balance calculation needs a full year of dekadal ET₀ data to calculate the water balance.

Irrigation amounts. This setting is important for use in irrigated rice simulations.

Crop data.

Crops. Which crops are grown? Each crop has its own crop coefficients.

Planting dekads. In which dekad planting occurred?

Cycle length of the crops grown.

Soil related input data

Water Holding Capacity of the soil.

Percentage Effective Rainfall. This parameter is non-essential and is usually kept at 100%. It is meant to account for run-off (values lower than 100%) or run-on (values higher than 100%)

Pre-season crop coefficient. This is the “crop” coefficient for bare soil (usually around 0.15).

Preparing a simple water balance calculation

After checking the availability of data a water balance can be prepared through the function Water Balance – Monitoring Run – New.

The following window is shown. A new name the run is specified. “Afghanistan Wheat 2003” is specified. A station list called "Rainfall monitoring network" is selected as a basis for the weather data. The selected crop is wheat. This crop is cultivated in almost all districts of Afghanistan, partly supplied with water trough irrigation.

In the following screen all the data needed for the water balance are entered. All rainfall and PET are entered elsewhere.

In an over-simplified example the same values are assigned to all stations. The water balance will be refined later. The cursor is put in the planting dekad column and the following button is pressed

The value of 1 is assigned to the planting dekad. This means that we assume that the wheat crop is planted in the first dekad of January for all stations in the list.

After press Ok, the planting dekad column is filled with the value 1. The same is done for the following columns. The following values are assigned to the next columns:
Cycle length : 15 dekads
Water Holding Capacity of the soil : 60 mm
Percentage effective rainfall : 100 %
Pre-season Kcr : 0.15
Irrigation application : 0 (this means NO irrigation)
Irrigation bund height : 0

In the end the window is filled as follows:

Refining the water Balance

In the prvious section a very simple Water Balance calculation is completed. The same values have been assigned to the water balance parameters for all stations. In this paragraph the water balance calculation is made more realistic by calculating realistic planting dekads and adding irrigation.

Calculating planting dates

Measured values are always the best data around. So if planting dates are available they should be used. However a good approximation of planting dates can be figured out with rainfall records. Planting usually occurs as a result of rainfall exceeding a certain amount. AMS can calculate the planting dates based on this simple algorithm. Activate the Water Balance – Monitoring Run – Calculate planting dekads – Based on Rainfall Threshold function. In this example it is assumed that planting occurs when 20 millimeters of rainfall has been exceeded.

Retrieved from "http://hoefsloot.com/wiki/index.php?title=Chapter19"

CM Box User Guide	Main Page \| About \| Special pages \| Log in
	Printable version \| Disclaimer \| Privacy policy \| Current revision

The following window is shown. A new name the run is specified. “Afghanistan Wheat 2003” is specified. A station list called "Rainfall monitoring network" is selected as a basis for the weather data. The selected crop is wheat. This crop is cultivated in almost all districts of Afghanistan, partly supplied with water trough irrigation.
In the following screen all the data needed for the water balance are entered. All rainfall and PET are entered elsewhere.
In an over-simplified example the same values are assigned to all stations. The water balance will be refined later. The cursor is put in the planting dekad column and the following button is pressed
The value of 1 is assigned to the planting dekad. This means that we assume that the wheat crop is planted in the first dekad of January for all stations in the list.
After press Ok, the planting dekad column is filled with the value 1. The same is done for the following columns. The following values are assigned to the next columns: Cycle length : 15 dekads Water Holding Capacity of the soil : 60 mm Percentage effective rainfall : 100 % Pre-season Kcr : 0.15 Irrigation application : 0 (this means NO irrigation) Irrigation bund height : 0 In the end the window is filled as follows: